2N6489 DATASHEET PDF

2N 2N 2N DESCRIPTION. ·With TO package. ·Excellent safe operating area. ·Complement to type 2N 2N 2N respectively. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N datasheet, 2N circuit, 2N data sheet: MOSPEC – POWER TRANSISTORS(15A,75W),alldatasheet, datasheet, Datasheet search site for.

Author: Kira Kar
Country: Panama
Language: English (Spanish)
Genre: Spiritual
Published (Last): 4 March 2014
Pages: 102
PDF File Size: 6.64 Mb
ePub File Size: 16.41 Mb
ISBN: 783-5-75343-520-4
Downloads: 91969
Price: Free* [*Free Regsitration Required]
Uploader: Douran

In order to determine Vz, consider Figure l-3b.

(PDF) 2N Datasheet PDF Download – Trans GP BJT PNP 40V 15A 3-Pin(3+Tab) TO Box

See Section 2 for voltages available R: They lead to what is termed a “load dump” problem. These can be classified into three types: The addition of three more similar networks and a quad operational amplifier makes dataeheet a simple matter to protect all four outputs against short circuits. Now a variety of these circuits are on xatasheet market and widely used. In the case of a single transistor con- verter, however, it is usually more cost effective to directly drive the transistor from the IC Figure 1 B.

The block diagram of the MC is shown in Figure In this section, guidelines will be given on proper regulator layout and placement of circuit components. The circuit shown in Figure may be used with almost any type of regulator circuitry; however, the circuit shown in Figure should only be used in linear type supplies where the filter capacitor is isolated from the line.

The regulator will tend to keep Vo constant 2n649 sensing any changes in Vo and trying to return it to its original value.

A bleeder resistor is normally used here not only for safety but to mask the differences in leakage current. For example, line and load regulation for the 5. The output frequency will now be equal to that of the oscillator. Because both emitters are at an ac ground point, expensive drive trans- formers can now be replaced by lower cost capacitively coupled drive circuits.

  ANTECEDENTES PREHISPANICOS DE LA PSIQUIATRIA EN MEXICO PDF

If this return lead is physically connected between the load return and the regulator circuit ground point “B”a ripple voltage component 60 or Hz can be induced on the load voltage, Vl.

To use the guide, first locate the problem’s symptom s and then carefully recheck the reg- ulator design in the area indicated using the information contained in the referenced handbook section.

Vin — Vout min d. This is done by using an external pass element and a zener level shifter as shown in Figure B.

HTTP This page has been moved

The effective current limit of today’s low cost TO-3 transistors mil die is somewhere in the 10 to 20 A area. While overcoming the disadvantages of the zener sense datasyeet, this tech- nique requires many components and is more costly.

If the sensing circuit has low immunity and is operated in a noisy environment, nuisance tripping of the OVP circuit can occur on short localized noise spikes, which would not normally damage the load. Simple Coil Here the designer must recheck three areas: The magnitude of the positive output voltage is equal to and tracks the negative output voltage.

Returning to the above curves, the full- wave circuit will be considered. The 50 kHz output is filtered by inductor LI, and capacitor C4. The resulting output voltage-current characteristic is shown datasheeh Figure B. Control Section Dataseet TL provides the pulse- width modulation control for the power supply. In many instances the designer must empirically determine the SCR and circuit elements which will result 2n689 reliable and effective OVP operation. Welcome to the ECE Store.

Transistors

In this section, several circuit configurations and design equations are given for the various regulator ICs. Improper circuit configuration 4 18 3 Loss of Regulation at Heavy Loads 1. Engineering Program is accredited by: The two transistor variation of this circuit Figure C eliminates the clamp winding and adds A. Unfortunately, there is no exact step-by- step procedure that can be followed which will lead to the ideal regulator and circuit configuration for a specific application.

  LIBRO SOCIALISMO DEL SIGLO XXI HEINZ DIETERICH PDF

The curves shown in Figures through give all the required design information for half- wave and full- wave rectifier circuits. Low Vio drift amplifier 2. The reverse bias drive removes stored charge quickly — within 2 u,s — and then causes the transistor’s base to avalanche for the short while it takes to reset the transformer. Half-load regulation is equally impressive.

Also, a trend has begun toward higher switching frequencies to further reduce size and cost.

Basic Pulse Width Modulator Control IC Features required by a control IC vary to some extent because of the particular needs of a designer and on the circuit topology chosen. This feature can be used to obtain thermal shutdown when the regulator’s junction temperature limit is exceeded, as shown in Figures G and G; to latch the output when a short 22n6489 occurs, as shown in Figure G; or to remotely shut down the regulator during standby periods in battery operated equipment.

This may result in the average current capability of the SCR datashdet the steady state current require- ments imposed by the dc power supply. If line 3 datassheet less than line 2, use a larger rectifier or increase R s – 3. To minimize component count, an IC is offered which performs this function in a single package: Relation of applied alternating peak voltage to direct output voltage in full- wave capacitor-input circuits.