ASTM A – Standard Specification for Electric-Fusion – Free download as PDF File .pdf), Text File .txt) or view presentation slides online. Standard. Buy ASTM A SPECIFICATION FOR ELECTRIC-FUSION (ARC)- WELDED STEEL PIPE (NPS 4 AND OVER) from SAI Global. pipes, UNS K, Electric-fusion, (Arc-) welded, straight seam or spiral seam, steel pipe 10 – mm diameter inclusive with nominal wall thickness up to
|Published (Last):||13 March 2004|
|PDF File Size:||13.32 Mb|
|ePub File Size:||18.55 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM A139 and ASME SA139 Carbon Steel Tubes
The suitability of pipe for various purposes is somewhat dependent on its dimensions, properties, and conditions of service. Questions or comments about MatWeb? We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error.
All burrs at the ends of pipe shall be removed. The pressure shall be determined by the following equation: Subscribe to Premium Services Searches: The minimum wall thickness at any point shall be not more than The steel shall be made by one or more of the following processes: The pipe is intended for conveying liquid, gas, or vapor.
Data sheets for overmetals, plastics, ceramics, and composites. Heat analysis of a193 heat of steel was made to determine the percentage of the elements as per chemical requirements.
Thickness The minimum wall thickness at any point shall be not more than Listing of standardized dimensions are for reference Note 2. Yield strength,min Ksi Mpa.
Spiralco – Specifications – ASTM A
Circumference The pipe shall be substantially round. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
The pipe shall be substantially round. This is a summary of ASTM specifications. One reduced-section production weld test specimen shall be taken from a length of pipe from each lot of ft. Straightness Finished pipe shall be commercially straight.
For example, for a1139 service see applicable codes and Specification A The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC. Link to Active This link will always route to the current Active version of the standard.
When agreed upon by the purchaser and the manufacturer and so stated on the order, pipe may be tested: The steel shall conform to the following chemical requirements: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The outside circumference of the pipe shall not vary more than 1. This specification covers five grades of electric-fusion arc -welded straight-seam or spiral-seam steel pipe in 4″ to 92″ inclusive with wall thickness up to 1 ” inclusive.
We appreciate your input. Tensile strength ,min Ksi Mpa. ASTM does not give any warranty express or implied or make any asmt that the contents of this abstract are accurate, complete or up to date. This abstract is a brief summary of the referenced standard.
ASTM A Steel, grade B
Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
Repairs of this nature shall be made by completely removing the defect, cleaning the cavity, and then welding. Or if you don’t have an account with us yet, then click here to register. All awtm pipe shall be subject to hydrostatic testing. This specification covers five grades of electric-fusion arc -welded straight-seam or helical steel pipe including pipe of NPS 4 and over. One longitudinal tension test specimen shall be made from the steel of each heat, or fraction thereof, used in the manufacture of the pipe.
Historical Version s – view previous versions of standard. When agreed upon by the purchaser and the manufacturer and so asmt on the order, pipe may be tested:. Pipe of NPS 4 Note 1 and larger with nominal average wall thickness of 1.
The required chemical composition, tensile requirements of the steel, and the tensile requirements of the production welds are presented. For additional details and information, please refer to these specifications.
The grades of steel are pipe mill grades having mechanical properties which differ from standard plate grades. Login to see your most recently viewed materials here. Electric-fusion, Arc- welded, straight seam or spiral seam, steel pipe 10 – mm diameter inclusive with nominal wall thickness up to 25 mm inclusive.