ASTM A463 PDF

ASTM A – Designation: A /A M – 02a Standard Speci?cation for Steel Sheet, Aluminum-. Find the most up-to-date version of ASTM A at Engineering ASTM A/AM: Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process.

Author: Malalkis Vudogami
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Love
Published (Last): 17 January 2005
Pages: 218
PDF File Size: 3.6 Mb
ePub File Size: 11.37 Mb
ISBN: 389-5-95491-485-7
Downloads: 77788
Price: Free* [*Free Regsitration Required]
Uploader: Gadal

H Shall be furnished as a stabilized steel. This abstract is a brief summary of the referenced standard. This is not considered to be a fault of the steel but is rather a function of the induced cold-work.

Your comments are invited either for revision of this standard or for additional standards and ast be addressed to ASTM International Headquarters. Within the text, SI units are shown in brackets. All other values in Table X2. They are solely to provide the purchaser with as much information as possible to make an informed decision on the steel to be speci?

ASTM A463 Grade FSS-439

We appreciate your input. Because of the many variables and changing conditions that are characteristic of continuous q463 coating lines, the weight [mass] of coating is not always evenly divided between the two surfaces of a sheet, nor is the coating evenly distributed from edge to edge. D If a higher tensile strength is required, the user should consult the producer. Structural steel and high strength low alloy steel shall conform to the mechanical property requirements.

This standard has been approved for use by agencies of the Department of Defense. Click here to view all the property values for this datasheet as they were originally entered into MatWeb. Values outside of these ranges are to be expected. C these ranges are to be expected. Originally published as A astj 62 T. The satm analysis of the base metal shall conform to the requirements specified.

  ADELPHIA COMMUNICATIONS SCANDAL PDF

Continuing dialogue between users and producers will have to be maintained to assist in a4663 transition to the new designation system. These factors 3 include: Those who use these documents must determine which speci?

Titanium is permitted for SS steels to 0. Flaking of the coating within 0. C When a deoxidized steel is required for wstm application, the purchaser has the option to order CS and FS to a minimum of 0. MatWeb is intended for personal, non-commercial use.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

C As there is no discontinuous yield curve, the yield strength should be taken as the stress at 0. Each system shall be used independently of the other.

Users requiring more precise data for scientific or engineering calculations can click on the property value to sstm the original value as well as raw conversions to equivalent units.

These notes and footnotes excluding those in tables and? When the amount of vanadium, titanium, or columbium is less than z463. NOTE 1—Typical ordering descriptions are as follows: If the hardness result is 85 HRB or higher, no tension test is required.

Inch-pound to SI conversions are reliable to?

ASTM A Aluminum-Coated Steel, Type I, Drawing Quality

In such cases, the applicable limit for vanadium and columbium shall be 0. Please contact us at webmaster matweb. Data sheets for overmetals, plastics, ceramics, and composites.

  AYE GOMORRAH PDF

For all designations the coating bend test inside diameter shall be equal to twice the thickness of the specimen. The purchaser shall specify the appropriate table of thickness tolerances in Speci? They are intended solely to provide the purchaser with as much information as possible to make an informed decision on the steel to be speci?

B No minimum means that there are no established minimum requirements for triple- and single-spot tests, but aluminum coating shall be present.

We also ask that you refer to MatWeb’s terms of use regarding this information. G Shall not be furnished as a stabilized steel. The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC.

B These typical mechanical properties apply to the full range of steel sheet thicknesses. Aluminum-coated type 1 steel, coils or cut sheet Coated with aluminum-silicon alloy by hot astmm process Used for combustion aatm, exhaust systems, heat exchangers and reflectors, ovens, grills, and appliances Vendors: Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

B Weight [mass] to thickness conversions are reliable to only two signi? Link to Active This link will astk route to the current Active version of the standard. A One ounce of Type 1 aluminum coating per square foot of surface corresponds to an average coating thickness of 0. These mechanical property values are nonmandatory.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.