ASTM A53 is a carbon steel alloy, used as structural steel or for low-pressure plumbing. The alloy specifications are set by ASTM International, in specification ASTM A53/A53M. This standard is issued under the fixed designation A53/A53M; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM A53 / A53M Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless.
|Published (Last):||25 August 2006|
|PDF File Size:||7.54 Mb|
|ePub File Size:||1.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM A53 / A53M Standard specification
Supplementary requirements of an optional nature are provided and shall apply only when specified by the purchaser. Our team are highly trained and experienced in servicing and producing all types of steel supplies. It is suitable for welding, and suitable for forming operations involving coiling, bending, ast flanging, subject to the following qualifications: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
The term nominal wall thickness has been assigned for the purpose of convenient designation, existing in name only, and is used to distinguish it from the actual wall thickness, which may vary over or under the nominal wall thickness. From Wikipedia, the free encyclopedia.
Sets standards for coating of pipe with zinc inside and outside by the hot-dipped process.
It is suitable for welding, and suitable for forming operations involving coiling, bending, and flanging, subject to the following qualifications:. This specification covers seamless carbon steel pipe for high-temperature service Sizes Seamless: Types and Grades This specification covers the following types and grades: It is commonly available astn national pipe thread ends or with plain cut ends.
This abstract is a brief summary of the referenced standard. These supplementary requirements call for additional tests to be made and when desired shall be so stated in the order. It is also weldable and can be used in structural applications, although ASTM A tube, aastm is available in the same NPS sizes, is sometime preferred.
It is suitable for welding, and suitable for forming operations involving coiling, bending, and flanging. Application of ASTM A53 Standard Aztm Steel Pipes ordered under this specification is intended for mechanical and pressure applications and is also acceptable for ordinary uses in steam, water, gas, and air lines.
Note 3—See Appendix X1 for definitions of types of pipe.
The steel categorized in this standard must be open-hearth, basic-oxygen or electric-furnace processed and must have the following chemical requirements: Continuous-Weld — Bending, flattening, tensile. Note asmt dimensionless designators NPS nominal pipe size [DN diameter nominal ] have been substituted in this specification for such traditional terms as “nominal diameter,” “size,” and “nominal size.
Asttm or XS, or wall thicknesses less than 0.
The hydrostatic test shall be applied, without leakage through the weld seam or the pipe body. This standard does not purport to address all of the safety concerns, if ast, associated with its use.
The minimum wall thickness at any point shall not be more than The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Weight of coating must not average less than 1. It is informational only and not an official part of the standard; the full text of the a533m itself must be referred to for its use and application. Hydrostatic inspection test pressures for plain end and threaded and coupled pipe are specified.
If Type S or Type E is required for close coiling or cold bending, Grade A is the preferred grade; however, this is not intended to prohibit the cold bending of Grade B pipe.
ASTM A53 ERW clarinet carbon pipe / ASTM A53/A53M
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It shall be permissible to furnish pipe having other dimensions provided such pipe complies with all other requirements of this specification.
It is informational only and not an official part of the standard; aa53m full text of the standard itself must be referred to for its use and application. Type E is furnished either nonexpanded or cold expanded at the option of the manufacturer.