ASTM A666-10 PDF

ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.

Author: Yozshutaur Moogubei
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Music
Published (Last): 13 December 2010
Pages: 364
PDF File Size: 18.36 Mb
ePub File Size: 13.21 Mb
ISBN: 366-2-48234-825-2
Downloads: 3288
Price: Free* [*Free Regsitration Required]
Uploader: Yozshut

Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques. Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. Material Test Report and Certi? Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications.

This standard is subject to revision a666-10 any time by the responsible technical committee and must be reviewed every?

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? In case of dispute, the offset method of determining yield strength shall be used.

Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool.

  BOSCH VDA-WMT-DOME PDF

6a66-10 and L cannot be hardened by thermal treatment. Type L LN Originally approved in HardC Elongation in 2 in. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard has been approved for use by agencies of the Department of Defense.

A number in parentheses indicates the year of last reapproval. Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides.

and L Stainless Steel – NKS

If filler metal is required, Type is normally used. Hard Elongation in 2 in. Permission rights to photocopy the standard may also be secured from the ASTM website www. D PSS means plate, strip, sheet.

Current edition approved Sept. In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres.

Last previous edition approved in as A — Only annealed conditions of grades speci? HRC typical L Ann 25 min. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.

A — 10 Standard Speci? C Annealed material that naturally meets mechanical properties may be applied. Rockwell B 95 95 One bend test shall be made from one end of each coil.

  GARUDA PURANA GUJARATI PDF

Maximum unless otherwise indicated. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Number of Tests 8. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: These alloys represent an excellent combination of corrosion resistance and fabricability.

Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

The noncontrolling factor normally will exceed considerably the speci? This revision of Speci? However, in the case of dispute, tests shall be made by pressure.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

304 and 304L Stainless Steel

The values given in parentheses are for information only. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Find out what NKS can do for you.