ASTM D6272 PDF

ASTM D – Air Permeability of Textile Fabrics . ASTM D – Standard Test Method for Flexural Properties Testing of Unreinforced and Reinforced. The Flexural test ASTM D measures the force required to bend a plastic beam under a four point loading system. The test method is used for reinforced or . ASTM D tests flexural properties of unreinforced and reinforced plastics and electrical insulating materials by four point bending. Learn more.

Author: Samukree Tejinn
Country: Lesotho
Language: English (Spanish)
Genre: Love
Published (Last): 15 February 2014
Pages: 477
PDF File Size: 19.94 Mb
ePub File Size: 20.27 Mb
ISBN: 921-1-51830-276-3
Downloads: 13342
Price: Free* [*Free Regsitration Required]
Uploader: Mooguktilar

Three recommended support span-to-depth ratios are The arc of the loading noses in contact with the specimen shall be sufficiently large to prevent contact of the specimen with the sides of the noses see Fig.

Alternatively, slack r6272 can be used to ensure that the calculations are performed on the appropriate section of the testing data. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

If specimen depth exceeds the width, buckling may d272. Five specimens are typically tested. The major difference between four point and three point bending modes is the location of the maximum bending moment and maximum axial fiber stress.

It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements. Precision and Bias The test method is used for reinforced or unreinforced materials including high modulus composites and for materials that do not fail within the limits of ASTM D a three point loading test.

  ALLGEMEINER AUFSICHTSZETTEL PDF

Since the flexural properties of many materials can vary depending on temperature, rate of strain and specimen thickness, it may be appropriate to test materials at varied parameters. Suitable for both dynamic and static testing, the 3-Point Bend Fixture easily provides the capability of a 3-point flexure test.

However, flexural strength cannot be determined for those d627 that do not break or that do not fail in the outer fibers. Onsite Training D622 Your Facility. The values provided in asm are for information only.

Instron ASTM D Flexural Properties of Plastics and Electrical Insulating Materials – Instron

Calculation NOTE 11—In determination of the calculated value of some of the dd6272 listed in this section it is necessary to determine if the toe compensation see Annex A1 adjustment must be made. NOTE 4—Whenever possible, the original surface of the sheet shall be unaltered. Load span to support span can be a ratio of 1 to 2 or 1 to 3. The challenges of testing to this standard are: If the material does not break, this part of the test is not applicable.

NOTE 1—Radii of cutouts match radii of noses and supports. Number of Test Specimens 8.

ASTM D6272 Flexural Properties of Plastics and Electrical Insulating Materials

Z shall equal 0. Wstm simple steps as follows can improve the repeatability of your results when using these adjustable span? Select from list below: This standard has either been superseded and replaced by a new version or discontinued. The specimen is supported on two lower anvils and the load is applied in the center of the specimen by a single upper anvil. Xstm flexure test requires a 4 point fixture where the bottom span is set by the span-to-depth of All dimensions must be stated in the report see also Note 6.

  ANTINUTRIENTES EN LOS ALIMENTOS PDF

Next Checking to see if you are a returning visitor…. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Link to Active This link will always route to the current Active version of the standard. An approximate correction factor is given in Eq 7 and 8 to correct for these end forces in large support span-to-depth ratio beams where relatively large de?

How can we help you?

The device shall automatically and continuously record the de? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

The chamber has internal electric heaters aztm elevated temperatures and uses external carbon dioxide gas as a coolant for reduced temperatures. For anisotropic materials, flatwise and edgewise specimens may be tested. The major difference between the three point and four point flexural tests is the location of the bending moment. Dimensions of loading noses and supports must be speci?

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.