DANFOSS VLT 6011 PDF

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Brashura Tojaramar
Country: Liechtenstein
Language: English (Spanish)
Genre: Literature
Published (Last): 6 February 2009
Pages: 332
PDF File Size: 11.70 Mb
ePub File Size: 2.66 Mb
ISBN: 844-8-14431-246-2
Downloads: 11816
Price: Free* [*Free Regsitration Required]
Uploader: Zolot

Page 91 A test connector with the connections shown below is required for this Initialization is selected to reset the drive to its factory default settings test.

Page 72 Address format 1 through Data Character byte The byte for the 1 through address range has the following The buildup of data blocks depends on the type of packet. Reference Type Reference Type The example below shows dangoss the resulting reference is calculated when Preset references are used together with Sum and Relative references set in parameterReference Type.

Page 37 If there is a fault, the display reads: Check alarms section in this manual for possible causes of alarm. If there is a fault, the display reads: Lines 3 and 4 vvlt the display will offer an explanation. Status Output word ref.

Danfoss VLT 6011 AC Drive 175z7360 10 HP 30.0a Variable Speed Drive 174b5218

When the theoretical output frequency exceeds the preset value, the drive restarts the motor. Page 75 Example – Write a parameter value: Incoming power, motor wiring and control wir- They are used for serial communication and the common of digital ing should danfoes run in three separate conduits 60011 inputs 16 through The calculation is based on the mean value in kWh over one hour.

Address format 1 through Data Character byte The byte for the 1 through address range has the following The buildup of data blocks depends on the type of packet. The frozen In parameters throughDigital Inputs, the functions of reference can only be changed by means of Speed Up or Speed terminals 16 through 33 are selected.

  MAHMUD SHABISTARI PDF

Calculation Of Resulting Reference Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication. Got it, continue to print. Contact the Danfoss The output frequency is higher than parameterWarning: Page 4 VLT Start-up Inputs and Outputs Parameters through In this parameter group, the functions of the drive input and output terminals are defined.

Remove the cover with a parameter settings. All drives except VLTto V and VLTThe shield of the control wires must be grounded at the cable clamp at to V must be mounted directly to the wall with no spacers. Relay Outputs Relay Outputs Relay outputs 1 and 2 can be used to give the present status or a warning.

Drives with to and below to 17 in-lbs 1. Page 97 Warnings Alarms A warning will flash in line danfoxs, while an explanation is given dznfoss line 1.

Danfoss VLT AC Drive Z 10hp | eBay

In the VLTthe feedback signals [22] are also active in open loop operation. Relay Outputs Relay outputs 1 and 2 can be used to give the present status or a warning. HIGH reply Error message The parameter number used does not exist There is no write access to the 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 By pressing ‘print’ button you will print only current page.

Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication.

Page 43 Description of choice: The table below gives the operating data options for the dahfoss and Line 4 is the status line and the information is automatically generated second lines of the display. Conduit entries are result in drive failure when power is applied.

  CFHEADER CONTENT-TYPE PDF

Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b | eBay

Programming Operation and Display Danfosw through Using the Extend Menu key, it is possible to access to all the parameters for the drive. Warnings And Alarms Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults. Too long of a ramp 60111 time can Depends on the unit 1 to seconds cause sluggish operation.

This parameter group contains functions useful for troubleshooting the drive including operating data, data log and fault log.

The built-in proportional, integral, derivative PID controller in the drive maintains a constant condition pressure, temperature, flow, etc. The serial communication on the communication option card is not working. Page status line Graham, manufacturer of motor, and manufac- turer of driven equipment before selecting Description of choice: Terminal 53, Analog Input [V], parametergives the voltage value These parameters can be read through the serial communication port of the signal on terminal It shows that the drive is in auto mode, with remote reference, and that the motor is Data Item: This value can be reset using parameterReset of kWh Counter.

Subsequently, eight data-bits are transferred, corresponding to one byte. The Minimum Reference, set in parameterindicates the smallest in the system. The response time of the slaves is dwnfoss FLN is a registered trademark of Siemens. If there is more than one warning or alarm, the sum vllt the warnings or alarms will be shown. The unit for the reference can be dnfoss from the following table: