View and Download ELECTRIX WARPFACTORY insructions online. THE ULTIMATE VOCODER. WARPFACTORY Recording Equipment pdf manual download. Electrix WARPFACTORY Pdf User Manuals. View online or download Electrix WARPFACTORY Insructions. Electrix Warp Factory: Electrix» white noise rackmount unit», vocoder rackmount unit» Lower Order settings will give a more â€œgranularâ€ Warp effect, Electrix); manual (German, Electrix); manual (Spanish, Electrix).
|Published (Last):||17 December 2007|
|PDF File Size:||1.66 Mb|
|ePub File Size:||3.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
Post Mixer Mic or the Auto settings for the formant input will provide plenty of sonic possibilities. Also, you can hit a button or a footswitch to “freeze” the formant, allowing a fixed wah kind of effect where mamual envelop stays open. Subscribe to our free newsletter Subscribe. Did you find this review helpful? Setting the MIDI channel: Log in Become a member. Could be cool for blending vocals and recorded music. However, after playing with it for a little while I felt that I could get the hang of it pretty well.
ELECTRIX WARPFACTORY INSRUCTIONS Pdf Download.
manua The Robot Voice Effect ” With this setup, no audio source is required. Highly recommended if you can find one cheap. Vocoder rack, you plug a microphone, and you have a robot voice or with the internal oscillator or an external synthesizer if you want to sing notes.
It does have midi connections, which should allow sequencing of all controls, with the possibility of animating and midi syncing them. There’s a blend knob and a kill dry switch which doesn’t actually kill the dry, just drops it down another 12 dB or so. It offers up a ton of control, and in general the tones mxnual clear and of course vocoded!
The advantage of this setup in a live situation is that fadtory WarpFactory effect can be auditioned cued through the mixer while other sources are playing. Introduction As an added bonus, WarpFactory has a built in phono pre-amp so you can plug your turntable directly in. J ‘like red facade and large buttons, no need to have hands Missyas in too many devices, here welcome big paws.
ELECTRIX WARPFACTORY Insructions
Then I shall decide to ask a review on this troisme vocoder. Mixer with Aux Send Page 12 – Setup 3: There is definitely a good amount control over your tone, with control over both the mic preamp gain and mqnual ‘warping’ your signal. Bypass Output to the microphone input on the mixer. The bottom line with the Warp Factory is that if you are looking for a vocoder in a piece of outboard gear, definitely do not decide on one until you check out this one!
The msnual for the warp factory possde do not have a lot of grain in low and high registers. It’s been 3 months factoty that I think I owns and well under control. If you are are new to vocoding, I’d definitely suggest having the manual around. Pretty straight forward using CC messages. Note that a press and hold of the bypass button will dump the present state of the controls.
By pressing ‘print’ manjal you will print only current page. It does simple vocoding fairly well, probably digitally because there is a noticeable delay before the onset of the envelope opening.
Write a user review Ask for a user review. This allows you to cue the effect before it goes to the house by using the cueing feature of your mixer. When source kill is engaged, WarpFactory will only pass sound while eleectrix is a formant input.
Electrix Warp Factory User Manual
Tuning it higher does a kind of chipmunk, girlie man thing, pretty cool and probably even more useful if you’re using something other than voice as a formant generator.
When you stop talking into the microphone, WarpFactory will go quiet. First off, you can tune the formants either high or low, adjust the Q and the number of sampling bands from the front panel.
WarpFactory only while you are talking into a microphone that is plugged into the Formant mic input.
There’s a gain knob for the input, and one of Electrix traditional “scroll buttons” to choose inputs from mic to line, to auto, which will choose an input depending on which is active at the time. The only other hardware vocoders I’ve seen have been a LOT more.