FLYGT 3152 PDF

2. C C Product. Submersible pump for pumping clean water, surface water and waste water containing solids or long-fibred material. Denomination. Dataplate. rpm. Max 40°C. YSER/Y//V. 26/51A. kWhp. Date: Flygt CS MT. Use our handy online form to submit details on your existing Flygt pump to get a Flygt C Submersible Pumps Range Flygt C LT Submersible.

Author: Zulushakar Zulkikora
Country: Guatemala
Language: English (Spanish)
Genre: Photos
Published (Last): 25 June 2008
Pages: 496
PDF File Size: 1.9 Mb
ePub File Size: 10.37 Mb
ISBN: 845-1-49445-477-7
Downloads: 56777
Price: Free* [*Free Regsitration Required]
Uploader: Vudolrajas

Check that the cables do not have any sharp bends and are not pinched.

Product specifications | Flygt 3152 – Alaska Pump and Supply

Lifting device Check that local safety regulations are followed. The impeller is stuck. Remove the upper wear protection. Depending the pumps model, do the following.

The drive unit is not receiving full voltage on all three phases. Check that all valves are correctly installed according to media flow.

Connect the mains leads L1, L2, L3, and earth [ground] to the starter equipment. The data plate lists key product specifications.

Raise the stop level. Make sure that any thermal contacts incorporated in the pump are properly connected to the terminal board.

Flygt 3000 Series / C Submersible Pumps

Never lift the unit by the motor cable or by the hose. Make sure that dlygt pump is correctly connected to earth ground. Tightening torque, see Torque values page Hydraulic part Installation type Sales code Product code The product code consists of nine characters divided into two parts.

  16F877 TUTORIAL PDF

The density of the pumped fluid is too high. Remove the impeller and the wear protections For the HS-version, also remove the wear protections. If the pump is a PL-version, do the following. Connect the motor cable and the starter and monitoring equipment according to the separate instructions.

Flygt Series / C Submersible Pumps

Replace the oil plug O-rings. This rule applies to pumps and mixers as well as monitoring equipment. Voltage and amperage Check the running values. Do not pry off the impeller or the impeller hub since tlygt can easily be damaged.

Earthing Grounding Electrical Hazard: Use a rubber mallet or a wooden block to prevent deformation. LL Figure The oil housing may be pressurized.

Drain all liquid, if any. Always disconnect and lock lfygt power before servicing to prevent unexpected startup. Do not install the starter equipment in an explosive zone or in the sump.

Unscrew the four cap nuts and withdraw the lower wear protection from the pump housing. Safety regulations for Ex-approved products in potentially explosive atmospheres Guidelines for compliance Compliance is only fulfilled when the pump is operated within flygr intended use, for example within its intended hydraulic range. This rule applies to both ends of the cable.

Flygt – Alaska Pump and Supply |

There is a malfunction in the levelsensing equipment. FM approval plate Product denomination Flygt Installation, Operation, and Maintenance Manual 15 Product Description Sales denomination The sales denomination consists of the four-digit sales code and two letters that indicate the hydraulic end and type of installation. This guideline also applies to the control circuit.

  74HC164 SMD PDF

Make sure that the pump is isolated from the system and that pressure is relieved before flygf disassemble the pump, remove plugs, or disconnect piping. LL Replace the wear ring in the pump housing, diffuser ring, or suction cover Figure Clean chemicals from the body 1. Dispose of all packing materials in accordance with local regulations. Test the earth ground lead to verify that it is connected correctly.

Run the cable so that it has no sharp bends, is not pinched, and cannot be sucked into the pump inlet. Product warranty Coverage Xylem undertakes to remedy faults in products from Xylem under these conditions: Check that the impeller rotates according to this illustration. Connect the discharge pipe to the discharge connection. In addition to the data plate, explosion-proof products also have either an EN or a FM approval plate.

If the problem still persists: